28 Search Results

Hydrothermal liquefaction (HTL) of lignocellulosic biomass is plagued with low biocrude yields owing to the tendency of highly reactive oxygenated intermediates to condense to form biochars. By contrast, the high protein content in food waste is comprised of substantial nitrogen species, which are known to interact strongly with oxygenates through Maillard, amide, and peptide bond formation reactions. Co-feeding food waste and lignocellulose opens new reaction pathways for biocrude formation but is currently poorly understood. This work evaluated the molecular level interactions between food waste and lignocellulose model compounds and the corresponding effect on product yields and quality. Food waste–cellulose andmore » food waste–xylan feedstock blends achieved maximum biocrude carbon yield improvements of 12.2% and 10.1%, respectively, relative to a simple linear model that interpolates between the yields of the pure feedstocks. Increases in biocrude yield were balanced by corresponding decreases in char yield, indicating synergistic interactions between the feeds during HTL. Biocrude volatility analysis revealed that increased biocrude yield preferentially benefitted the jet fuel fraction, which comprised up to 22.6% of the total carbon yield for food waste–cellulose blends. Biocrude and char were analyzed using GC–MS and FT-IR spectroscopy to investigate the source of synergistic trends and provide greater mechanistic understanding. Key cofeeding effects included the promotion of retro-aldol condensation reactions and trans-esterification of fatty acids, sequestering carbon in the biocrude phase via the inhibition of char formation while increasing biocrude volatility toward jet fuel-range compounds. These results indicate the potential for judicious selection of HTL cofeeds to increase both biocrude yield and selectivity to desired fuel precursors, including sustainable aviation fuel.« less

While the levelized costs of electricity and heat have been quantified before, these two metrics cannot be directly compared, due to the different exergy content of heat and work. To address this, we develop a levelized cost of exergy (LCOEx) framework that enables direct comparisons between energy sources and processes. We find that moderate- and high-grade heat have an LCOEx that is comparable to electricity (5–10 ¢ per kWh_ex), while low-grade heat sources have much higher LCOEx values (>50 ¢ per kWh_ex). The LCOEx of a system's output is affected by (i) the LCOEx of the system input, (ii) themore » CAPEX of the system, and (iii) the exergetic efficiency of the system. We use our framework to identify which processes are already achieved with relatively high cost effectiveness (production of fuels, hydrogen, and ammonia) and which have room for improvement (dehumidification, food production).« less

Plant and fungal cell walls are essential for growth, adaptation, and survival, with their intricate architectures dictating both resistance to stress and susceptibility to antifungal or biomass-degrading strategies. Understanding how these walls are built, remodeled, and function at the molecular level is therefore central to both clinical and biotechnological applications. Solid-state nuclear magnetic resonance (ssNMR) has emerged as a uniquely powerful tool for this purpose, as it reveals the structure, dynamics, and interactions of intact biopolymers without disrupting their native organization. Using this approach, recent studies have shown how structural polymorphism, polymer-polymer interactions, and species-specific remodeling govern mechanical integrity, drugmore » resistance, and stress adaptation. Applications highlighted here include lignin-carbohydrate packing during plant stem maturation, fungal wall reorganization under treatment by wall-targeting antifungals such as echinocandin and nikkomycin, and the functional diversity of glucans, chitins, and mannans. Together, these insights uncover conserved principles of polymer assembly across kingdoms while informing new opportunities for antifungal development and biomass utilization. Ongoing advances in sensitivity and resolution are expected to broaden the reach of ssNMR and further accelerate its role in linking structural heterogeneity to biosynthetic complexity and biological function.« less

The plant secondary cell wall, a complex matrix composed of cellulose, hemicellulose, and lignin, is crucial for the mechanical strength and water-proofing properties of plant tissues, and serves as a primary source of biomass for biorenewable energy and biomaterials. Structural analysis of these polymers and their interactions within the secondary cell wall has been heavily relying on ¹³C-based solid-state NMR techniques. In this study, we explore the application of ¹H-detected solid-state NMR techniques for rapid, high-resolution structural characterization of polysaccharides and lignin, demonstrated on the stems of hardwood eucalyptus. We explored the use of synthesized 2D spectra to resolve centralmore » ¹H resonances and the combined application of 3D hCCH and hCHH experiments for complete resonance assignment and unambiguous identification of lignin-carbohydrate interactions. Our findings emphasize the central role of acetylated three-fold xylan conformers, rather than two-fold, in stabilizing the carbohydrate-lignin interface, with glucuronic acid sidechains in eucalyptus glucuronoxylan colocalizing with lignin, revised cellulose-lignin interactions involving uncoated microfibril surfaces, and pectin-lignin interactions indicative of early-stage lignification. These results present a novel approach for rapid structural analysis of lignocellulosic biomaterials without the need for solubilization or extraction.« less

Background: Time-of-flight secondary ion mass spectrometry (ToF-SIMS) is a powerful surface analysis technique, initially developed and applied in inorganic materials and semiconductors. In past decades, ToF-SIMS has attracted more attention in its analysis capabilities of organic materials, with increased applications in biology, medical, and health development. It has also become a versatile and effective tool in environmental analysis due to its high mass resolution, mass accuracy, and depth profiling. Results: In this review, we first give an overview of the principle of ToF-SIMS and follow with recent ToF-SIMS applications in exemplary environmental study cases, including atmospheric aerosol, soil, water, plant,more » and organic solvent analysis. Moreover, sample preparation techniques are summarized in relation to corresponding environmental applications. Specifically, we call attention to ToF-SIMS investigations showcasing studies in surface chemical compositions, images, and depth profile analysis. These findings emphasize the important role of interfacial chemistry in environmental processes and provide valuable insights into dynamic processes, such as chemical transformation, particle formation, plant biology, and microbial inspired biotechnology development. The mass spectral imaging results acquired by ToF-SIMS offer a deeper understanding of intermediate stages and transient phases for environmental specimens. Significance: In situ and operando imaging offer new possibilities in studying phenomena in real time with high spatial resolution. Furthermore, it is anticipated that more research groups will use ToF-SIMS in environmental research given recent advances in measurement capabilities and surging needs in chemical mapping of complex analytes and systems.« less

Plant cell walls are made of a complex network of interacting polymers that play a critical role in plant development and responses to environmental changes. Thus, improving plant biomass and fitness requires the elucidation of the structural organization of plant cell walls in their native environment. The ¹³C-based multi-dimensional solid-state nuclear magnetic resonance (ssNMR) has been instrumental in revealing the structural information of plant cell walls through 2D and 3D correlation spectral analyses. However, the requirement of enriching plants with ¹³C limits the applicability of this method. To our knowledge, there is only a very limited set of methods currentlymore » available that achieve high levels of ¹³C-labeling of plant materials using ¹³CO₂, and most of them require large amounts of ¹³CO₂ in larger growth chambers. In this study, a simplified protocol for 13C-labeling of plant materials is introduced that allows ca 60% labeling of the cell walls, as quantified by comparison with commercially labeled samples. This level of ¹³C-enrichment is sufficient for all conventional 2D and 3D correlation ssNMR experiments for detailed analysis of plant cell wall structure. The protocol is based on a convenient and easy setup to supply both ¹³C-labeled glucose and ¹³CO₂ using a vacuum-desiccator. The protocol does not require large amounts of ¹³CO₂. This study shows that our ¹³C-labeling of plant materials can make the accessibility to ssNMR technique easy and affordable. The derived high-resolution 2D and 3D correlation spectra are used to extract structural information of plant cell walls. This helps to better understand the influence of polysaccharide-polysaccharide interaction on plant performance and allows for a more precise parametrization of plant cell wall models.« less

Here, this essay aims to suggest research areas to which chemists and others in related fields can contribute, to help preserve and sustain the world for future generations by addressing problems of global importance.

Exposure pathways to the carcinogen benzene are well-established from tobacco smoke, oil and gas development, refining, gasoline pumping, and gasoline and diesel combustion. Combustion has also been linked to the formation of nitrogen dioxide, carbon monoxide, and formaldehyde indoors from gas stoves. To our knowledge, however, no research has quantified the formation of benzene indoors from gas combustion by stoves. Across 87 homes in California and Colorado, natural gas and propane combustion emitted detectable and repeatable levels of benzene that in some homes raised indoor benzene concentrations above well-established health benchmarks. Mean benzene emissions from gas and propane burners onmore » high and ovens set to 350 °F ranged from 2.8 to 6.5 μg min^–1, 10 to 25 times higher than emissions from electric coil and radiant alternatives; neither induction stoves nor the food being cooked emitted detectable benzene. Benzene produced by gas and propane stoves also migrated throughout homes, in some cases elevating bedroom benzene concentrations above chronic health benchmarks for hours after the stove was turned off. Combustion of gas and propane from stoves may be a substantial benzene exposure pathway and can reduce indoor air quality.« less

Abstract Background Microscopic analysis of plant anatomy is a common procedure in biology to study structure and function that requires high-quality sections for accurate measurements. Hand sectioning of specimens is typically limited to moderately soft tissue while harder samples prohibit sectioning by hand and/or result in inconsistent thicknesses. Results Here we present both a clearly described hand-sectioning method and a novel microtome design that together provide the means to section a variety of plant sample types. The described hand-sectioning method for herbaceous stems works well for softer subjects but is less suitable for samples with secondary growth (e.g., wood production).more » Instead, the “Rapid-Tome” is a novel tool for sectioning both soft and tougher high-aspect-ratio samples, such as stems and roots, with excellent sample control. The Rapid-Tome can be 3D-printed in approximately 18 h on a mid-quality printer common at university maker spaces. After printing and trimming, Rapid-Tome assembly takes a few minutes with five metal parts common at hardware stores. Users sectioned a variety of plant samples including the hollow internodes of switchgrass ( Panicum virgatum ), fibrous switchgrass roots containing aerenchyma, and woody branches of eastern red cedar ( Juniperus virginiana ) and American sycamore ( Platanus occidentalis ). A comparative analyses with Rapid-Tome-produced sections readily revealed a significant difference in seasonal growth of sycamore xylem vessel area in spring (49%) vs. summer (23%). Additionally, high school students with no prior experience produced sections with the Rapid-Tome adequate for comparative analyses of various plant samples in less than an hour. Conclusions The described hand-sectioning method is suitable for softer tissues, including hollow-stemmed grasses and similar samples. In addition, the Rapid-Tome provides capacity to safely produce high-quality sections of tougher plant materials at a fraction of the cost of traditional microtomes combined with excellent sample control. The Rapid-Tome features rapid sectioning, sample advancement, blade changes, and sample changes; it is highly portable and can be used easily with minimal training making production of thin sections accessible for classroom and outreach use, in addition to research.« less

We manufactured laboratory-scale food packages containing 2.57 ± 0.18 × 10^–3 wt% silver nanoparticles (AgNPs) and used them to show that table sugar (sucrose) and microcrystalline titanium dioxide (μTiO₂) enhance Ag migration from these packages and into aqueous food simulants. Ag migration into purified water was detected but was below the limit of ICP-MS quantitation, giving a range of potential Ag migration between 0.059 and 0.082 ng cm^–2 packaging surface area. Ag migration into 9 wt% aqueous sucrose solution was 0.547 ± 0.084 ng cm^–2 and migration into 9 wt% sucrose solution containing 0.01 wt% μTiO₂ was 0.724 ± 0.032more » ng cm^–2. Total Ag migration into a 0.01 wt% μTiO₂ aqueous dispersion without sucrose was between 0.122 and 0.162 ng cm^–2, with upper and lower limits defined by the detectability of Ag in the supernatant phase of the simulant. If the midpoint of this range is taken as a baseline, these results imply that, compared to purified water, Ag migration was increased by approximately 10.3 times when the water simulant contained μTiO₂ and sucrose at commercially-relevant concentrations. Notably, the Ag migrated into water containing both ingredients exceeded the total Ag migrated into either of the single-ingredient simulants, pointing to a potential cooperative relationship between sucrose and μTiO₂ that possibly derives from binding and redox interactions between these two ingredients. Sucrose and μTiO₂ also both reduced a portion of migrated Ag⁺ back into AgNPs, and μTiO₂ particles efficiently captured (>25% by mass) migrated Ag on their surfaces. Similar effects on migration were observed with nanocrystalline TiO₂. Furthermore, these experiments are the first to show that TiO₂ particles exert a strong influence on the quantity and form of Ag that could migrate from AgNP-enabled packaging, suggesting that food formulations and interactions between individual food components may be important to consider when evaluating the fate of nanoparticles in these consumer applications.« less